| |
|
 |
Millburn, NJ -- A 48-in (1220mm) diameter Circular Fluid Bed Dryer equipped with an integral circular vibratory screener quadrupled production of a proprietary granular chemical product, and improved quality by increasing the consistency of drying times.
Granules are Pre-Screened, Dried, Re-Screened
The product is comprised of a granular carrier material, a filler material and an active ingredient. The granular carrier is screened into a narrow size range using a 48-inch (1220 mm) diameter, two-deck Kason VibroscreenÒ circular vibratory screener, after which the filler material and active ingredient are added, and the batch undergoes a proprietary conversion process.
A 48-inch (1220 mm) diameter Circular Fluid Bed Dryer reduces moisture content of the converted material to less than 1.0 percent at 120° F (49° C), after which it is discharged into an integral 48-inch (1220 mm) diameter, two-deck Vibroscreen separator that removes (oversize) agglomerates and (undersize) fines, and discharges into storage containers at a rate of 2000 lb/h (907 kg/h).
Rectangular Fluid Bed Dryers Considered
The company’s engineering manager says he considered a rectangular fluidized bed dryer, but found it cumbersome and costly. Rectangular fluidized beds, he explains, “work fine but are twice as large as a circular unit, requiring massive infrastructure and ancillary equipment, and they require higher airflow, consuming more energy."
“We were impressed with the circulating unit’s small footprint, fluidizing action, speed of drying, and modularity¾you can move it without difficulty. We also had operating experience and a comfort level with circular vibratory screeners that look and function similar to a circular fluidized bed dryer,” he says.
Circular Fluid Bed Dryer/Screener Operation
Converted material from storage containers is fed into the top inlet of the dryer by a bucket elevator. In the fluid bed chamber, the material vibrates on a circular screen within a rising column of 120° F (49 °C) air created by an upstream heater/blower ducted into the bottom of the chamber. The continuous air-flow, and vibration induced by two vibratory motors and spring suspension, separate and fluidize individual particles, maximizing surface area and drying efficiency. The vibratory action also causes material to travel from the center of the screen to a discharge spout at the screen's periphery in controlled spiral pathways on a first-in-first-out basis, ultimately discharging dried material into the top-center inlet of the circular vibratory screener.
An imbalanced-weight gyratory motor positioned beneath the chamber of the screener vibrates two screening decks. Oversize particles travel in controlled spiral pathways from the center of the screen to a spout at the screen's periphery where they are discharged for reprocessing.
On-size and undersized particles pass rapidly through the top screen to a bowl-shaped feed tray that directs them to the center of the second screen. On-size particles travel in controlled spiral pathways to a spout at the screen's periphery where they are discharged, while undersize material passes through the screen onto an integral metal chute that discharges it through a third spout for reprocessing.
Analyze Separated Material
Since any increase in the ratio of active ingredient to carrier and filler increases the occurrence of aggolmeration, the company monitors the ratio of agglomerates to on-size material to detect whether any process variation has affected distribution of the active ingredient.
Since the drying-screening portion of the overall process operates off-line, it can also be utilized to dry raw materials containing excess moisture, or dry other bulk products manufactured by the company. In anticipation of wide-ranging drying applications, the system was engineered to operate at temperatures higher than that required to dry the proprietary chemical.
Improved Labor Utilization
According to the Engineering Manager, operators previously moved back and forth between tasks while waiting for product to dry, and were unable to focus adequate attention to either task, raising the chance for error. "Operators are now fully utilized in producing and drying the product, with significantly less error," he says, and reports that that the drying-screening system paid for itself in less than six months from combined productivity gains and labor savings.
Kason Corporation manufactures circular, vibratory, fluid bed processors for drying, cooling and moisturizing, and vibratory screeners and centrifugal screeners for separating solids from virtually any bulk solid material or slurry.
For information contact:
Kason Corporation
67-71 E. Willow St.
Millburn, NJ 07041-1416
Telephone: 973-467-8140
Email: info@kason.com
Web site: http://www.kason.com/
© Copyright 1998 - 2008 Powder and
Bulk Dot Com
Top of Page
|
|
| |
| Send news and case
histories to:
news@powderandbulk.com |
|
|
| |
|
|
|
I Live Newsfeed
I |
|
Increase traffic and add
content to your website
with our exclusive
newsfeed generator.
Our live newsfeed
allows you to
include news
headlines from our
News Center, right
on your homepage.
Headlines update in
real-time, automatically.
Click here to create
your own newsfeed! |
|
| |
|
 |
